Visit Website

 

 

They are making a few good pointers about Tools You Need to Install a New Bathtub overall in this article just below.

Installing a bathtub isn't exactly brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is additionally a reasonably difficult project. If the old bathtub is easily obtainable, the job can move easily; if you have to open up a wall surface to remove the old bathtub and position the brand-new tub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will require a helper to vacate the old tub and also set in the new one. See to it you have certified yourself for the task and also are comfortable trying it. Rather than employing a service provider to take over a halfway-completed task, it is better to think about using one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This short article will certainly help you set up a brand-new bath tub in your restroom if you have actually currently bought a new bathtub and also don't need to transform the arrangement of your previous water system pipelines.
Your tools and material list should comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Preparing for the Setup

To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.

 

 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be quite problematic due to the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

 

 

Setting up the Tub

Using both wooden boards under its feet, place the tub in the required position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub till the level reviews degree.
To install faucets, fit the bottom of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water system and also check all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bath tub and additionally check the overflow outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has been utilized at the very least when as this will settle it right into its last position.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The previous type should be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Tub

In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We were shown that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an acquaintance on another domain. Do you know about anybody else who is very much interested in the niche? Please feel free to share it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.

Book An Appointment